View KEH-P1015_151757.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

ENGLISH
INSTALLATION MANUAL
INSTALLATION MANUAL
ESPANOL
KEH-P1015
PORTUGUES(B)
www..com
This product conforms to new cord colors. Los colores de los cables de este producto se conforman con un nuevo codigo de colores. As cores dos cabos deste produto conformam com um novo codigo de cores.
Contents
Connecting the Units ................................ 2 Installation .................................................. 5
DIN Front/Rear-mount ...................................... 5 DIN Front-mount .............................................. 5 - Installation with the rubber bush - Removing the Unit DIN Rear-mount ................................................ 7 - Installation using the screw holes on the side of the unit
www..com
1
Connecting the Units
Note:
* This unit is for vehicles with a 12-volt battery and negative grounding. Before installing it in a recreational vehicle, truck, or bus, check the battery voltage. * To avoid shorts in the electrical system, be sure to disconnect the battery cable before beginning installation. * Refer to the owner's manual for details on connecting the power amp and other units, then make connections correctly. * Secure the wiring with cable clamps or adhesive tape. To protect the wiring, wrap adhesive tape around them where they lie against metal parts. * Route and secure all wiring so it cannot touch any moving parts, such as the gear shift, handbrake, and seat rails. Do not route wiring in places that get hot, such as near the heater outlet. If the insulation of the wiring melts or gets torn, there is a danger of the wiring short-circuiting to the vehicle www..com body. * Don't pass the yellow lead through a hole into the engine compartment to connect to the battery. This will damage the lead insulation and cause a very dangerous short. * Do not shorten any leads. If you do, the protection circuit may fail to work when it should. * Never feed power to other equipment by cutting the insulation of the power supply lead of the unit and tapping into the lead. The current capacity of the lead will be exceeded, causing overheating. * When replacing fuse, be sure to use only fuse of the rating prescribed on the fuse holder. * Since a unique BPTL circuit is employed, never wire so the speaker leads are directly grounded or the left and right speaker leads are common. * The black lead is ground. Please ground this lead separately from the ground of high-current products such as power amps. If you ground the products together and the ground becomes detached, there is a risk of damage to the products or fire. * Speakers connected to this unit must be highpower types with minimum rating of 45 W and impedance of 4 to 8 ohms. Connecting speakers with output and/or impedance values other than those noted here may result in the speakers catching fire, emitting smoke, or becoming damaged. * When this product's source is switched ON, a control signal is output through the blue/white lead. Connect to an external power amp's system remote control or the car's Auto-antenna relay control terminal (max. 300 mA 12 V DC). If the car features a glass antenna, connect to the antenna booster power supply terminal. * When an external power amp is being used with this system, be sure not to connect the blue/white lead to the amp's power terminal. Likewise, do not connect the blue/white lead to the power terminal of the auto-antenna. Such connection could cause excessive current drain and malfunction. * To avoid short-circuiting, cover the disconnected lead with insulating tape. Especially, insulate the unused speaker leads without fail. There is a possibility of short-circuiting if the leads are not insulated. * To prevent incorrect connection, the input side of the IP-BUS connector is blue, and the output side is black. Connect the connectors of the same colors correctly. * If this unit is installed in a vehicle that does not have an ACC (accessory) position on the ignition switch, the red lead of the unit should be connected to a terminal coupled with ignition switch ON/OFF operations. If this is not done, the vehicle battery may be drained when you are away from the vehicle for several hours. (Fig. 1)
ACC
ENGLISH
OF
OF
F
O
N
STAR
F
O
N
STAR
ACC position
No ACC position
* Cords for this product and those for other prod* Cords for this product and those for other products may be different colors even if they have the ucts may be different colors even if they have the same function. When connecting this product to same function. When connecting this product to another product, refer to the supplied Installation another product, refer to the supplied Installation manuals of both products and connect cords that manuals of both products and connect cords that have the same function. have the same function.
T
T
Fig. 1
2
Connecting the Units
IP-BUS cable
Rear output This Product Multi-CD player (sold separately) Antenna jack www..com Fuse IP-BUS input (Blue) Blue/white To system control terminal of the power amp or Auto-antenna relay control terminal (max. 300 mA 12 V DC).
Yellow To terminal always supplied with power regardless of ignition switch position. Red To electric terminal controlled by ignition switch (12 V DC) ON/OFF.
Front speaker
Left Black (ground) To vehicle (metal) body. Rear speaker
With a 2 speaker system, do not connect anything to the speaker leads that are not connected to speakers. Rear speaker Perform these connections when using a different amp (sold separately).
3
ENGLISH
Power amp (sold separately) Connecting cords with RCA pin plugs (sold separately) www..com
System remote control
White + White/black Green + Green/black
Gray + Front speaker Gray/black Violet + Rear speaker Violet/black Right
+
+ Rear speaker
Fig. 2
4
Installation
Note:
* Before finally installing the unit, connect the wiring temporarily, making sure it is all connected up properly, and the unit and the system work properly. * Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions. * Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle. * Install the unit where it does not get in the driver's way and cannot injure the passenger if there is a sudden stop, like an emergency stop. * If installation angle exceeds 30 from horizontal, the unit might not give its optimum performance. (Fig. 3)
30
Fig. 3
www..com
DIN Front/Rear-mount
This unit can be properly installed either from "Front" (conventional DIN Front-mount) or "Rear" (DIN Rear-mount installation, utilizing threaded screw holes at the sides of unit chassis). For details, refer to the following illustrated installation methods.
DIN Front-mount
Installation with the rubber bush (Fig. 4)
Holder After inserting the holder into the dashboard, then select the appropriate tabs according to the thickness of the dashboard material and bend them. (Install as firmly as possible using the top and bottom tabs. To secure, bend the tabs 90 degrees.) Rubber bush Screw
Dashboard
182
53
Fig. 4 5
Removing the Unit (Fig. 5) (Fig. 6)
ENGLISH
5 Frame
6nsert I
the release pin into the hole in the bottom of the frame and pull out to remove the frame. (When reattaching the frame, point the side with a groove downwards and attach it.)
Fig. 5
Insert the supplied extraction keys into the unit, as shown in the figure, until they click into place. Keeping the keys pressed against the sides of the unit, pull the unit out.
www..com
Fig. 6
6
Installation
DIN Rear-mount
Installation using the screw holes on the side of the unit
1. Remove the frame. (Fig. 7)
Frame Insert the release pin into the hole in the bottom of the frame and pull out to remove the frame. (When reattaching the frame, point the side with a groove downwards and attach it.) www..com
Fig. 7
7
2. Fastening the unit to the factory radio mounting bracket. (Fig. 8) (Fig. 9)
Select a position where the screw holes of the bracket and the screw holes of the head unit become aligned (are fitted), and tighten the screws at 2 places on each side. Use either truss screws (5 8 mm) or flush surface screws (5 8 mm), depending on the shape of the screw holes in the bracket.
ENGLISH
10
www..com
Fig. 8
11 Screw
13 Dashboard or Console
Factory radio mounting bracket 12
Fig. 9
8
www..com
PIONEER CORPORATION
4-1, MEGURO 1-CHOME, MEGURO-KU, TOKYO 153-8654, JAPAN
PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, California 90801, U.S.A. TEL: (800) 421-1404 PIONEER EUROPE NV Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: (0) 3/570.05.11 PIONEER ELECTRONICS AUSTRALIA PTY. LTD. 178-184 Boundary Road, Braeside, Victoria 3195, Australia TEL: (03) 9586-6300 PIONEER ELECTRONICS OF CANADA, INC. 300 Allstate Parkway, Markham, Ontario L3R OP2, Canada TEL: (905) 479-4411 PIONEER ELECTRONICS DE MEXICO, S.A. de C.V. San Lorenzo 1009 3er. Piso Desp. 302 Col. Del Valle Mexico, D.F. C.P. 03100 TEL: 5-688-52-90
Published by Pioneer Corporation. Copyright (c) 2000 by Pioneer Corporation. All rights reserved. Publication de Pioneer Corporation. Copyright (c) 2000 Pioneer Corporation. Tous droits de reproduction et de traduction reserves. Printed in Imprime

▲Up To Search▲

Price & Availability of KEH-P1015

	To Download KEH-P1015 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .